Federal Ballistics Calculator – Use Free Online

Work out the drop, drift, velocity, and energy of any of 366 Federal factory loads with this calculator, covering 72 calibers and built on Federal’s published figures. Choose your load and shooting conditions, and it draws the full trajectory out to 2,000 yards in a table and a chart.

Federal’s catalogue runs from light varmint cartridges to heavy magnums, and this tool gathers its published ballistics in a single place. It needs no sign in, stores nothing about you, and works in any modern browser.

Federal Ballistics Calculator

Factory loads from Federal Premium published data. Pick a load, set your conditions, and get drop, wind drift, velocity, energy and time of flight. Calculated values come from a point-mass solver; the Published Data tab shows the Federal table exactly as printed.

Units: Load type:
Factory load

Ballistic coefficient: –

Handload

Enter the BC for the drag model selected below. Use the G1 number for a G1 BC, the G7 number for a G7 BC.

1.5 bolt-action, 2.6 MSR

Positive uphill, negative downhill

Environment and wind

Auto-raises to 1000 for long-range calibers. Cap 2000.

Elevation / windage units (each adds a drop and wind column pair)

Calculated results are estimates from a point-mass solver using the published muzzle velocity and ballistic coefficient, standard G1/G7 drag models, and your conditions. They are not Federal published values. The Published Data tab shows the Federal table exactly as printed on the product page. Always confirm a firing solution on paper at the real distance before use.

How Do You Use the Federal Ballistics Calculator?

  1. Start in Factory Load mode and select a caliber. The bullet style choices appear first, then the weights, then the muzzle velocities, and the G1 BC fills itself in.
  2. Enter your sight height (1.50 inches to start), zero range (100 yards to start), temperature (59 F to start), wind speed (10 mph to start), and wind direction.
  3. Choose a range step (10, 25, 50, or 100 yards) and a longest range (500 yards to start, up to 2,000 yards).
  4. Hit Calculate. You get a table of range, drop, wind drift, velocity, energy, and time of flight for every step. Turn on MOA or MIL to add those columns beside the inch columns.

For a handload, change to Handload mode and enter a description, bullet style, bullet weight, muzzle velocity, and BC of your own before you hit Calculate. Factory loads and handloads run through the same solver.

Open the Published Data tab to see the chosen load’s factory table printed exactly as Federal published it, with velocity, energy, wind drift, and trajectory at the distances Federal lists. The chart below the table draws the drop curve and the drift curve for your load. Compare mode places a second load next to the first, and the print and copy buttons save your results.

Federal Ballistics Calculator Loads and Results: What Is Inside?

Inside the tool are 366 Federal factory loads spread over 72 calibers, each one carrying a published muzzle velocity and a published G1 BC. 57 of those loads carry a G7 BC as well, and 360 of the 366 carry published downrange tables with velocity, energy, and wind drift to 500 yards, along with trajectory sets for a 100 yard zero and a 200 yard zero.

The tool figures drop, wind drift, velocity, energy, and time of flight to any range up to 2,000 yards, using whatever zero range, sight height, temperature, wind speed and direction, humidity, pressure, and shooting angle you set. You can read the answers in inches, MOA, MIL, or all three at once, and the Imperial/Metric toggle converts every figure.

Its solver was tested against the factory table for the 308 Win ELD-X 178 gr load: at 500 yards it gives 1,864 fps where Federal prints 1,872 fps, which is about a 1 percent gap.

CartridgeLoadBullet Weight (gr)Muzzle Velocity (fps)G1 BC
308 WinELD-X17826100.552
6.5 CreedmoorELD-X14327000.625
223 RemFusion Soft Point6230000.310
223 RemFusion Soft Point622750–

Frequently Asked Questions

  1. What does the Federal Ballistics Calculator do?
    It works out drop, wind drift, velocity, energy, and time of flight for Federal loads at any range you choose, up to 2,000 yards.
  2. Does it cost anything?
    No, it is free, and it needs no account or registration.
  3. How many loads can I pick from?
    There are 366 factory loads in 72 calibers, all with published muzzle velocities and G1 BC values.
  4. Can I enter my own handload data?
    Yes. Handload mode lets you type the bullet style, weight, muzzle velocity, and BC yourself.
  5. Where do the numbers come from?
    Every load comes from Federal’s published product data, and the Published Data tab shows the factory table exactly as printed.
  6. What is the longest range it covers?
    It goes to 2,000 yards. It starts at 500 yards and moves to 1,000 yards on its own for long range calibers.
  7. Is there a metric option?
    Yes. Switching to metric converts all the values, from sight height to maximum range.
  8. Will it work on my phone?
    Yes. On a small screen the controls stack, the tables scroll sideways, and the chart fits the width.
  9. Should I pick G1 or G7?
    Use G1 unless your load publishes a G7 BC. 57 of the loads in the tool publish a G7 value, and the toggle uses it when it is there.
  10. How do I keep a copy of my results?
    Use the print button for a printed sheet, or the copy button to copy the whole table as text.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *