JBM Ballistic Calculator – Online Free
Run a trajectory for any bullet with the JBM Ballistic Calculator, built on JBM’s drag tables and a length list of 3,521 bullets from 49 makers. You choose the bullet and enter a ballistic coefficient and muzzle velocity, and the calculator returns drop, drift, velocity, energy, time of flight, and a stability figure, out to 2,000 yards.
There are no factory loads here, because JBM makes no ammunition. Every BC and muzzle velocity in a result is one you typed in, while the drag curves and bullet lengths come from JBM’s own published reference data.
Table of Contents [Click to minimize]
JBM Ballistic Calculator
Pick a bullet from JBM’s bullet length list (3,521 bullets, 49 makers), enter your ballistic coefficient and muzzle velocity, and get drop, wind drift, velocity, energy, time of flight and gyroscopic stability. Drag tables and bullet lengths are JBM reference data. JBM publishes no BC or muzzle velocity for any bullet, so those two fields are your entries.
Diameter: – Weight: – Length: –
JBM publishes no BC or muzzle velocity. Enter your own BC for the drag model selected below (G1 number for G1, G7 number for G7). Muzzle velocity is always entered in feet per second, in Imperial and Metric modes. The twist rate is used for the stability calculation only. BC 0.462 and 2700 fps are shown as an example for the 168 gr MatchKing; replace them with your figures.
1.5 bolt-action, 2.6 MSR
Positive uphill, negative downhill
Cap 2000.
Same conditions, drag model and twist as the first bullet.
Calculated results are estimates from a point-mass solver using your entered muzzle velocity and ballistic coefficient with JBM drag tables. JBM publishes no loaded ammunition, no factory loads, and no BC or velocity figures; bullet lengths come from JBM’s bullet length list. Stability uses the Miller twist rule with the Courtney-Miller correction for plastic-tipped bullets. Always confirm a firing solution on paper at the real distance before use.
How Do You Use the JBM Ballistic Calculator?
- Start with the bullet picker. Select a maker, then a caliber, then a bullet from JBM’s length list, or search by name. For a bullet that is not listed, pick Custom bullet and enter the length by hand.
- Type in the ballistic coefficient and the muzzle velocity for your load. JBM publishes no BC and no velocity figures, so these two fields are never filled in for you.
- Add your barrel twist, such as 1:12. The calculator needs it for the stability figure.
- Enter the sight height (1.50 inches as standard), the zero range (100 yards as standard), the temperature (59 F), the wind speed (10 mph), and the wind direction.
- Choose how the table steps out: a range increment of 10, 25, 50, or 100 yards, and a maximum range from 500 yards up to 2,000 yards.
- Hit Calculate to get the table, with range, drop, wind drift, velocity, energy, and time of flight at each step. Add MOA or MIL columns beside the inch columns if you want them.
A stability factor is shown with every result, worked out by the Miller twist rule with the Courtney-Miller correction. The default bullet, a Sierra 168 gr MatchKing in a 1:12 twist at 2,700 fps, scores Sg 1.72, which counts as Stable.
Open the JBM Data tab to see the chosen bullet’s entry from the length list and the drag table behind the result. The chart below the table draws the drop curve and the wind drift curve, compare mode puts a second bullet alongside the first, and the print and copy buttons save the results.
What Is Inside the JBM Ballistic Calculator?
The calculator runs on JBM reference data and nothing else. It holds every one of the 9 JBM drag functions, G1, G2, G5, G6, G7, G8, GI, Sphere, and RA4, exactly as published, 730 points in all, and a picker built from the 3,521-bullet length list, which spans 49 makers and 104 calibers.
Since JBM sells no loaded ammunition, the calculator carries no factory loads and no published BC or velocity numbers. The ballistic coefficient and muzzle velocity come from you in every case. Of the 3,521 bullets, 853 (24.2 percent) have no length on record, and for those the trajectory still works while the stability figure does not, because the Miller rule cannot run without a length.
Anything up to 2,000 yards can be worked out: drop, drift, velocity, energy, and time of flight, for whatever zero, sight height, temperature, wind speed and direction, humidity, pressure, or shooting angle you set. Read the results in inches, MOA, MIL, or a mix of the three, and switch between Imperial and Metric to convert every value.
As a check, the trajectory was run against the Federal calculator’s validated solver with identical inputs (308 Win 178 gr, BC G1 0.552, 2,610 fps), and at 500 yards it returned the same figures: 1,864 fps, 1,374 ft-lb, 18.6 in of drift, and -60.8 in of drop.
| Bullet | BC | Muzzle Velocity (fps) | Twist | Stability (Sg) |
|---|---|---|---|---|
| Sierra 0.308 168 gr HPBT MatchKing | 0.462 | 2700 | 1:12 | 1.72, Stable |
| Range (yd) | Velocity (fps) | Energy (ft-lb) | Drop (in) | Wind Drift (in) |
|---|---|---|---|---|
| 500 | 1864 | 1374 | -60.8 | 18.6 |
Questions About the JBM Ballistic Calculator
Does the JBM Ballistic Calculator cost anything?
No. It is free to use in your browser, with no account and no payment.
Where do the BC and muzzle velocity come from?
From you. JBM publishes no loaded ammunition, so the calculator has no factory BC or velocity figures to offer.
How do I find my bullet in the picker?
Pick the maker, then the caliber, then the bullet, or search by name. When a bullet is not in the list, use Custom bullet and type in its length.
What is Sg?
Sg is the Miller gyroscopic stability factor, with the Courtney-Miller correction applied. Values above 1.0 count as stable, and the default Sierra 168 gr MatchKing scores 1.72 at a 1:12 twist.
Can I still calculate a bullet with no published length?
Yes for trajectory. The 853 bullets without a length still give drop, drift, velocity, and energy, but no stability figure, because the Miller rule needs the length.
What drag models are included?
All 9 of JBM’s: G1, G2, G5, G6, G7, G8, GI, Sphere, and RA4, with 730 points exactly as published.
What is the longest range it covers?
2,000 yards, with 500 yards as the default maximum.
What is the JBM Data tab for?
It shows the selected bullet’s stored length-list entry and the drag table used for the calculation.
Will it work on my phone?
Yes. The form stacks, the inputs are 16px, the buttons are 44px tall, the tables scroll sideways, and the chart fits the screen.
Can I save or share my results?
Yes. The print button opens a print friendly view, the copy button copies the table as text, and compare mode lets you place two bullets side by side.